Burson Audio Conductor Stellar Headphone Amplifier & DAC

There are all manner of desktop-style combination headphone amplifiers and DACs available, but do they all work well with all the many different kinds of headphones that there are out there?

Headphones and earphones use all manner of drivers, some with a dozen of them for each side. Some have an impedance of 600 ohms, others as little as 16 ohms – perhaps even less – with the majority leaning more towards the lower figure than the higher one. Some have a dead-even impedance curve across the audible spectrum, while others vary wildly in impedance. Some will produce enormous sound levels for almost no power, while others require a high-ish voltage, plenty of current, or both.

Australian company Burson Audio has long been producing quality headphone amplifiers, and its Conductor Stellar is specifically designed to be versatile, with particular attention to supporting modern IEMs – in-ear monitors.

About the Burson Conductor Stellar

First, some manufacturer’s specifications:

High gain maximum output power

32 ohms, balanced/single ended: 8 watts/4 watts

100 ohms, balanced/single ended: 5 watts/2.5 watts

150 ohms, balanced/single ended: 3.5 watts/2 watts

300 ohms, balanced/single ended: 1.1 watts/0.52 watts

IEM mode maximum output power

32 ohms, balanced/single ended: 1000mW/500mW

100 ohms, balanced/single ended: 500mW/250mW

150 ohms, balanced/single ended: 250mW/125mW

300 ohms, balanced/single ended: 100mW/60mW

Headphone output impedance: 0.5 ohm

Frequency Response: 0 – 55kHz +/-1dB

THD: <0.0015%

Signal to Noise ratio: >105dB (high gain), >100dB (IEM)

Inputs: 1 x USB-C, 1 x optical digital, 1 x coaxial digital, Bluetooth 5.0, Microphone

Outputs: 1 x 3.5mm IEM, 1 x 6.25mm headphone, 1 x 4-pin XLR balanced headphone, 2 x XLR for balanced stereo DAC OUT/PRE OUT, 2 x RCA for single ended DAC OUT/PRE OUT

Digital support: S/PDIF inputs, PCM to 24-bit, 192kHz; USB, PCM to 32-bit, 768kHz and DSD, native or DoP to DSD512; Bluetooth, LDAC, aptX HD, AAC, SBC

Included accessories: 24V 5A power supply, Remote control, USB cable, Mic adaptor, 12V trigger cable, spare fuse, hex key, spare IC op amps for trouble shooting.

Dimensions: 210mm deep by 200mm wide by 75mm tall

Weight: 5kg

Manufacturer Website here.

User manual here.

Price: Deluxe version: $3,849; Max version (with 24V Fusion Core power supply): $4,749

From: Here.

About the Burson Conductor Stellar headphone amplifier

Okay, there’s a lot there. Here are the things I think are important.

First, an extremely low impedance for the headphone outputs; just 0.5 ohms. Second, stacks of power; well and truly plenty for even the most troublesome headphones. Third, almost complete support for whatever digital music you may have in your possession (your player will decode those old WMA files to PCM!) Fourth, a truly solid and impressive build.

I shan’t describe the appearance of the Burson Conductor Stellar headphone amplifier. Instead, I’ll merely remark how very handsome it is and otherwise direct you to the photos. I particularly like the copper highlights. The front panel display shows input, output, volume level and the sampling frequency of the current signal.

The power is full Class-A – you’ll soon notice how very hot the casing gets, even when idling.

One of the special features offered by Burson is the ability to upgrade the op amps and the power modules. This model – the Deluxe – includes the high end V7 Vivd PRO opamps. Others are available from Burson, or from other suppliers. Burson actually encourages you to experiment with these, and assured me that warranty coverage in unaffected. Likewise, the Silent Power02 modules help provide and exceptionally low noise floor, but you can swap these for others as well.

Think of all this as the solid-state equivalent of tube rolling.

There are optical, coaxial and USB-C inputs, plus Bluetooth. That last supports, in addition to the basic SBC codec, LDAC, aptX HD and AAC. The USB-C input is principally for plugging in computers, and indeed I used it extensively that way with JRiver Media Center on a Windows computer. I downloaded the driver from Burson’s website for this and used the ASIO option. No driver is required for Macs.

The USB-C input also supports Android phones with OTG functionality and iOS devices. As I write, Spotify is streaming from my Samsung Galaxy S25 via wire, rather than Bluetooth.

There are three headphone outputs on the front panel: 3.5mm, 6.25mm and balanced 4-pin XLR. The first one is labelled IEM. In the menu shown on the front panel you can select between four output modes: IEM, headphone, DAC OUT and PRE OUT. With either of the first two, all the headphone outputs are active, but in IEM mode they are supplied by the lower-powered separate balanced amplifier module intended for IEMs.

Don’t worry about the lack of a 4.4mm balanced headphone output; a 4.4mm to 4-pin balanced adaptor is included.*

Rear panel outputs provide for connecting to other equipment, via either regular RCA outputs or XLR balanced ones. It is for these that you choose either DAC OUT or PRE OUT. DAC OUT provides a fixed line level output (2 volts or 4 volts balanced), suitable for use with a preamplifier. PRE OUT puts the preamplifier in line, allowing outputs of up to 12 volts RMS, and of course you can control the volume. So you could use that directly with a power amplifier or active loudspeakers.

There is one disappointment, here, that seems to be quite common in this field: there are no analogue inputs. My turntable has no digital output. Oh, the Sound Burger has Bluetooth, but that’s not my go-to for vinyl. I can’t listen to it with this unit, although I would have liked to. One extremely rare feature I would also have liked would be the unit accepting DSD64 via its coaxial input.

The unit runs on 24V DC. The Deluxe unit comes with a 5-amp power pack, which notionally offers up to 120 watts. I was supplied with the Max version, which adds 24-volt (360 watts!) Fusion Core power supply. This is styled to harmonise with the Conductor Stellar.

Listening with the Burson Conductor Stellar headphone amplifier

Further down in this review I’ve got lots of rather technical stuff and a bunch of measurements. Much of this is because the unit is so very configurable, and more because I really wanted to wallow in the pleasure of so many unimpeachable aspects of the performance of the Burson Conductor Stellar. So let’s have a listen first, shall we? For these tests I chose mostly used the default settings, changing only to the MPFRO reconstruction filter, and switching the DAC bypass options completely off.

The Burson Conductor Stellar is a serious bit of kit, so I shall start with some serious music: the B-52’s debut album. That’s the one with “Rock Lobster”. I only half jest on “serious”; give it a listen if you know it only by reputation. I chose the Final Audio D8000 planar magnetic headphones, fitted with an after-market balanced cable, for this one. The album mostly doesn’t have great tonal depths, but the solid, punchy performance is well balanced. The strong rhythm line on “Planet Claire”, while not super deep, is powerful. The amplifier just loped along, thoroughly comfortable with impressive levels at a mere 46/99 indicated volume with the high gain setting.

These headphones have a relatively high impedance for planar magnetic headphones: 60 ohms. I switched over to the very budget-friendly FiiO JT7 planar magnetics. They are 6dB less sensitive than the D8000s and have an impedance of just 18 ohms. They are brighter than the D8000s, and nowhere near as smooth, as befits their 95% lower cost. But they are just as responsive.

Blood, Sweat and Tears’ “And When I Die” from a band compilation CD came through very nicely indeed, with the volume wound up to 55/99. Especially noticeable: the dynamic subtleties in the drums delivered to perfection. Every time I put on these headphones, I marvel at the price/performance ratio. So long, that is, that whatever is driving them is comfortable with the combination of low impedance and low sensitivity. The Burson was very comfortable indeed.

I switched over to a 1962 recording (delivered on CD via optical, as were all of the above) of Beethoven’s Opus 61 Violin Concerto on Deutsche Grammophon, and this time I used Focal Elear dynamic headphones (80 ohms, open backed, 6.25mm connection). I used to love these headphones. When I got them, they seemed way, way better than what I then had. But since then I’ve become very partial to planar magnetics. And there was no doubt about it, when the music really swells up around nine minutes into the first movement, the Elear headphones became a little unruly, confused even. Even the JT7 headphones, while less sweet with the solo violin, was more controlled in this section, while the D8000 headphones were immaculate.

Does that mean that the Burson isn’t so good with dynamic headphones? I tried some others. First, my very old Sennheiser HD 535 headphones (150 ohms, single-ended connection). They’re a bit brighter than the Focals, more like the JT7s. And they controlled things rather better than the Focal headphones. Interesting. The Focal Elear headphones are not a current model.

I must have played that section a dozen times. Including using Beyer-Dynamic DT 770 PRO headphones (the 250-ohm model). They demanded a lot more volume from the Burson, and it was happy to deliver. And that section of the music retained a proper composure.

That’s always the problem with reviewing equipment. How much of what you’re hearing is due to the equipment under review and how much is due to other equipment you’re using with it?

I do still like the Focal Elear headphones, but they’re not quite right for mass orchestral music recorded with multiple microphone techniques in the early 1960s.

But the Burson Conductor Stellar is. As we’ll see, thanks to its extremely low output impedance and massive reserves of power, and a stunningly flat frequency response, any weaknesses that you hear will be entirely due to the headphones or earphones.

Speaking of which, I used the unit briefly with Final Audio B3 IEMs (my favourites), Audiofly AF180Mk2 IEMs, and Sennheiser IE 300 IEMs. I tried them all both with the dedicated IEM output and with an adaptor with the 6.35mm output. All worked perfectly well and delivered what they were designed to do, sounding identical with both outputs. The B3 earphones have a crazy impedance curve (nominally 19 ohms) due to their twin balanced armature drivers. They can sound way off with an amplifier with even a few ohms of impedance on its output. Here, nothing. They were receiving a dead flat frequency balance from the Burson, and consequently performed optimally.

They seemed to sound a little different when I set the unit to IEM mode: a slightly recessed bass and a touch of harshness in the higher frequencies. I was puzzled because I hadn’t realised at that point that IEM mode employed a different amplifier module. Later, when I measured the output, I found that the frequency response and distortion and noise levels were identical in this mode, so I started to doubt what I’d heard.

But the measurements also showed that this output was 4dB quieter than the regular amplifier running in High Gain mode. More importantly, there really was a difference that caused what I was hearing. We’ll see what that was in the “Power Galore” section below.

Generally the unit is highly usable, except for the volume control which takes a lot of winding to get back up to listenable levels after it resets to 5/99 when certain modes are changed.

The remote control is a beautifully machined unit, entirely in keeping with the looks of the Burson Conductor Stellar. There is a trick to using it: you need to tap any key to wake it up, and then things like the volume controls work (much faster than using the knob). If you just pick up the remote and hold down the volume key, nothing will happen.

Oh, also, the mute button on the remote also works to play/pause a FiiO portable CD player and vice versa.

Microphone?

I was puzzled by a couple of things. One was a setting which allows one to set the microphone on or off. Microphone? And then there was this weird Y-adaptor included in the accessory box. It had two 3.5mm sockets and 4-pole 3.5mm plug.

I have an old set of Sony MDR-ZX310 on-ear headphones in my collection. These date from the days when all phones had a wired socket for headphones … and a microphone for hands-free conversations. And this has a similar 4-pole 3.5mm plug. If that setting is “On” and the Burson is plugged into your computer, the computer will think that it has a microphone plugged in, and that the “microphone” is the Burson. I was able to record my voice on my computer, using the Conductor Stellar as an audio interface. The Y-adaptor is for those who have separate plugs for the headphones and microphone.

Ideal, I suppose, for gamers and streamers.

Power galore

I only have the facilities to measure single-ended power outputs, and I do that at 16 ohms and 300 ohms. Into 16 ohms with the main amplifier, the unit easily delivered a clean 4.5 watts per channel. That’s more than 36dB above the sensitivity rating any headphones. Even low sensitivity headphones are above 90dB/mW. If they could take it, the Conductor Stellar could drive them to 126dB!

My 300-ohm measurement is directly comparable to Burson’s specification. It places this for single-ended at 170mW. I measured 250mW (24dB above 1mW), a healthy surplus.

Remember, the IEM output setting actually uses a different amplifier module, intended to be lower in power. In my measurements it still came in at 650mW into 16 ohms (28dB above 1mW), and 91mW into 300 ohms (19.5dB), which was 50% higher than specification.

I measured the output impedance for the main single-ended headphone output at just 0.57 ohms, close enough to specification. In IEM mode it came in at … 11 ohms. That was a surprise.

Remember, during my critical listening I noted that I thought I’d heard some differences with the IEM setting, but with a performance identical to that of the headphone output in terms of frequency response, noise and distortion, I was beginning to think it was imaginary.

Now I understand why. The B3s have a fairly uneven impedance curve, rising slowly from the bass through the midrange, coming to a significant peak near 3kHz, then falling away rapidly to 4kHz, before rising again even more, all the way to 20kHz. The 11 output ohms is relatively high compared to the nominal 19 ohms of the IEMs, so you hear that peak up around 3kHz and in the upper treble. It’s probably only a decibel or two, but it makes a difference.

My takeaway: forget about the IEM output setting. If you have very sensitive IEMs that you want to use, just use the Headphone output setting with the gain set to low, and start off with a low volume. Even with a high gain, there was nothing audible produced when the volume was at 5/99 in my gear. I think you’ll find a plenty of operating space down there, with no problems at all with noise.

DACs

The Burson Conductor Stellar employs the ESS Sabre ES9039PRO DAC. This is the current flagship model from the company. Some people quibble about whether ESS or Asaki Kesei DAC ships are better. In fact, their high end DACs are both state-of-the-art and until someone conducts a proper double-blind comparison that demonstrates a replicable difference, I shall continue to assume that claims of audible differences are imaginery.

The ES9039PRO DAC is thing of technical beauty. I might be a little dismissive of audible differences, but I do very much believe in overdoing it with performance. If you can, why not and remove any fears of limitations? So this DAC chip has not two channels, but eight. With an artful arrangement of these channels one can achieve ridiculously high signal to noise ratios, ridiculously low distortion levels. And I love all these ridiculous levels.

The chip natively supports PCM to 768kHz and 32 bits, and 16 x DSD (aka DSD1024).

Its headline dynamic range is an incredible 132dB! If all eight channels are folded into mono mode, that pushes out to 140dB. Either way, the noise level of the DAC chip is going to be well below that of the amplification, whether built into the unit such as with the Burson Conductor Stellar, or in a main stereo amplifier.

As I always do with DACs, I checked out what signals it was comfortable with. Optical from a CD player? Check! Coaxial from a streamer? Check! Asynchronous digital audio via USB-C? Check!

In each case, the display shows you the sampling rate, a feature I consider vital if you’re using the USB connection. It is all too easy to select the wrong output with your player software (especially with Windows), and accidentally have the computer perform sample rate conversion. With Windows 11, I could use Window’s own WASAPI driver, or an ASIO driver downloaded from Burson’s website. I’d recommend ASIO, especially if you like Direct Stream Digital. The Conductor Stellar does support DSD via WASAPI, but only in DoP (DSD over PCM) format, in which the DSD is disguised to look like it’s PCM. That is an inefficient process, so it limits the maximum to DSD256. I know, I know, surely DSD256 is plenty! I agree. Nonetheless, some content may one day be released on DSD512 and it would be nice to be able to play it.

So I used the ASIO driver and tested the unit with everything all the way up to DSD512 – I do have one track – and PCM at 705.6kHz and 768kHz. (I created those two test tracks myself.) It worked fine.

Reconstruction filters

There are some extremely unusual settings available for the DAC chip in this unit. We’ll deal with them shortly but first let’s look at the reconstruction filter choices available on this unit.

Burson doesn’t offer all seven of the filters built into the ESS9039PRO, but it makes four available:

LPAFR = Linear Phase Apodizing Fast Roll-off

MPFRO = Minimum Phase Fast Roll-off (this one is also listed as MP in the options)

MPSRO = Minimum Phase Slow Roll-off

MPSROLD = Minimum Phase Slow Roll-off Low Dispersion

Not available is LPFRO – Linear Phase Fast Roll-Off – which in my opinion most accurately reconstructs the original analogue signal. That said, I doubt that anyone could hear the difference. I certainly can’t, and I suspect the majority of people who think they do are imagining it.

The frequency responses of all of these are just what I’d expect from the ESS9039PRO DAC. Here they are for a 44.1kHz input signal:

The blue trace is hiding behind the purple one. As always, I recommend fast roll-off. That’s the green trace, which goes all the way to 20kHz.

Now have a look at this:

What you’re seeing there is a 192kHz test signal with the MPFRO filter. Things to note: the left and right channels are perfectly matched (0.02dB difference – which might be my measurement rig), and the output is just about ruler flat all the way up to 40kHz, and down by perhaps 0.15dB at 80kHz! That’s showing the DAC chip performance, of course, but this is also via the headphone amplifier, so it shows the quality of the analogue section.

Noise levels were excellent, too. With 24-bit test signals, here are the relative noise levels from the unit with DAC OUT selected and the main headphone amplifier (with its volume at 60/99 with High gain):

DAC OUT has the absolute minimum of electronics after the DAC chip. The headphone level was up pretty high, but even so the very highest peaks of mains harmonic noise was at a totally inaudible at -114dB. The blue trace is also from the DAC OUT, and mostly matches the white trace, except that that one was with the 5-amp power supply rather than the Fusion Core power supply. As you can see, there’s a bit more mains noise.

The A-weighted figures for those noise levels were -118.9dB for the DAC OUT and -102.7dB for the headphone.

And here’s the harmonic distortion graphs:

Again you get a bit more from the headphone out, but not very much more at all. Impressive. The A-weighted figures were 0.0003% for the DAC OUT and 0.0009% for the headphones.

Finally, here’s how the IEM output compared to the main headphone output for noise (volume levels shown):

And distortion:

These were with 44.1kHz 16-bit test signals so the performance wasn’t as good as the 24-bit signals. Nonetheless, you can see they’re almost identical with each other, with the main headphones exhibiting a little more mains breakthrough. Still, at -105dB its fine. The A-weighted results were -101.2dB for noise with the IEM output, and -99.5dB for the headphone. For distortion, it was 0.0028% and 0.0029%.

Settings, settings galore!

The Burson Conductor Stellar goes way beyond offering mere filter options for tweaking the ES3039PRO. It also allows you to adjust such things as the Image Rejection Ratio Bandwidth (IRR BW), the Digital Phased Lock Loop bandwidth (how tightly the unit locks onto the incoming signal), which level of in-chip THD compensation is applied, and even which steps of in-chip processing should be employed or skipped.

What on earth they all do? Let’s have a look. Warning, this is all really nerdy stuff.

The ESS DAC chip performs several steps of oversampling and filtering internally. I did a fairly deep dive on the options that you can skip. This comes under the name DAC Path. I mostly used an 11.025kHz “sine wave”, sampled at 44.1kHz, to illustrate what it does. I use quotes there, because with that signal the digital data is actually two identical high-level positive samples, followed by two negative ones, and with all this continuously repeated. Here’s a picture of what this looks like (these are captures of the output as shown on my oscilloscope):

Just think of those samples being at the corners of the square wave. In fact, this was the output of the Burson Conductor Stellar of this test signal when I set the DAC Path to “BP All”, that is, to have it bypass all the upsampling and filtering.

By contrast, when I set it to “No BP” – no bypass, so the chip completes all its processing – it looks like this:

Which is how it is supposed to look, having been properly “reconstructed” by the various filters.

Before looking at the other settings, let’s see what effect this has on a more reasonable test signal. Here’s the effect of this setting with a 1kHz sine wave:

Properly reconstructed (ie “No BP”):

If you count the steps in the first one, you’ll see that there are 44 in one cycle. That’s because there is no upsampling and no filtering. This is in effect a “NOS” – Non-Oversampling – “Filter”. If you are a fan of NOS DACs, even though one isn’t listed amongst the filter options, you can achieve the same end by bypassing all the processing within the DAC chip.

My recommendation: don’t. The output is full of ultrasonic mirror images of the sound. It’s probably inaudible, but if you feed the line outputs to an amplifier with weaknesses when it comes to intermodulation distortion, you may get to hear something unfortunate.

Back to the 11.025kHz test. Out of the box, or after you do a full settings reset to restore factory defaults, the DAC Path setting is “BP IIR”. Let’s see what that looks like:

Oh, stairsteps again! But in this case, what you’re seeing is the results of the ESS chip upscaling to 352.8kHz and then skipping this filtering step. Count the steps: there are 32 per cycle, and 32 times 11.025kHz is 352.8kHz. Since those steps are there, this must normally be the last filtering step in the sequence, otherwise one of the other reconstruction filters would have wiped them out. I don’t know what skipping this step is supposed to achieve, but my inclination would be to switch it off and go back to “No BP”.

When upsampling, this chip upsamples first by 2x and then by 4x (so, overall by 8x). The 4x step is next to last. If this is skipped, the output looks like this:

And if you skip the 2x step, it looks like this:

Disagree if you like, but I’d stick with “No BP”.

One extra note: one thing disclosed by the 11.025kHz bypass test is how stunningly good the analogue stage is. Look at those very near perfect square waves, the effectively instantaneous rise times. Simply excellent.

Intersample overs and pre-emphasis flags

Since we’re digging in here, let’s look at two things that almost no other reviewers look at. First, intersample overs. That’s where two digital audio samples are both close to other, and close to 0dBFS in the digital stream. They can result in the decoded analogue signal actually going above the level matching 0dBFS. Naively, that’s easily dealt with by simply having a bit of headroom in the analogue stage.

But most modern digital to analogue converter chips upsample internally (as we’ve seen, you can skip this with the Burson Conductor Stellar, at your peril), which causes those “intersample overs” to clip.

Until recently in ESS DAC chips, the only way to avoid this – something which, to be fair, happens only for a very small proportion of samples in probably a minority of tracks – has been to do some complicated design work to digitally lower the input signal to the chip by 3dB. But DAC chips like the ES9039PRO now have their internal digital volume control before any upsampling occurs, so they can reduce the level by 3dB if told to do so by the designer, totally eliminating the problem. Thus, this is the output from the headphone socket with one of the worst-case test signals (11.025kHz with all samples at 0dBFS):

If you use the rear connections and select PRE OUT, you get a similarly smooth, unclipped sine wave. But if you use DAC Out, you get that clipping, thus:

It’s clear that Burson has used the 3dB digital attenuation with the headphones and the PRE OUT stage. Both of these run through the V7 Vivid op amps. But it hasn’t with the DAC Out option.

I think this is interesting. Now, the DAC OUT setting is rated at delivering two volts (via RCA), which is pretty much the standard for line outputs for consumer digital devices, established way back in the 1980s with the CD player. A 3dB attenuation would reduce this to 1.414 volts. But, the whole point of DAC Out is to deliver as pure a signal as possible to downstream devices, so Burson wouldn’t have wanted to place an analogue boost stage after it. So I’m guessing that Burson, given the choice between the largely inaudible “problem” of intersample overs and departing from the output standards, chose the former.

But it is something to be aware of. If you believe this to be a problem, then select PRE OUT instead and adjust the level to suit your preamplifier. As for me: this is the frequency spectrum of the worst case test:

You can see the distortion products to the right of the 11.025kHz test frequency, but note, even the lowest one is at 22.05kHz and the rest are well above that. So long as your amplifier isn’t so poorly designed that this introduces harmonic distortion, you simply won’t be able to hear any of it.

The final technical note: the unit does not act upon the pre-emphasis flag in a stream from a CD transport. So a very small number of very old CDs may have excessive treble. Chances are you don’t have any in your collection.

Conclusion

So there you have it. The Burson Conductor Stellar is a truly high end headphone amplifier and DAC. It looks the part, but it also contains the parts that provide unimpeachable performance. I’d suggest a couple of changes to the default settings, as outline above. Adding the Fusion Core power supply does offer some further mains isolation. It’s probably not necessary, but if you believe in overkill, getting it as part of the “Max” configuration, rather than buying it separately, will save you several hundred dollars.

* This inclusion isn’t listed in the manufacturer’s specifications or manual. I have sought confirmation from Burson.

Burson audio, Dacs, Desktop headphone amps and dacs